EN 10327 PDF free download
Definition
This European Standard specifies requirements for continuously hot-dip coated strip and sheet made of low carbon steels for cold-forming coated with zinc (Z), zinc-iron alloy (ZF), zinc-aluminum alloy (ZA), aluminum-zinc alloy (AZ), and aluminum-silicon alloy (AS) with thicknesses of 0,35 mm to 3,0 mm unless otherwise agreed. The thickness is the final thickness of the delivered product after coating.
Classification
They are classified in accordance with their increasing suitability for cold forming as follows:
DX51D: bending and profiling quality;
DX52D: drawing quality;
DX53D: deep drawing quality; DX54D:
special deep drawing quality;
DX55D: special deep drawing quality, (only +AS), heat resistance up to 800 °C;
DX56D: extra deep drawing quality;
DX57D: super deep drawing quality
EN 10327 Equivalent
Standard: AISI, ASTM, BS, DIN, GB, JIS, etc
ASTM A653M SS GRADE 340,
ASTM A653M SS GRADE 255
ASTM A653M CS TYPE A,
ASTM A653M CS TYPE B
AS 1397 G450
JIS G3302 SGCC,
EN 10327-DX51D, DX53D, DX54D, DX51D+Z,
EN 10326-S250GD
Steel grade and mechanism property
Designation | Chemical composition % by mass | Yield strength R a MPa * | Tensile strength Rm MPa * | Elongation A80 b % min. | Plastic strain ratio r90 min. | Strain hardening exponent n90 min. |
|||||||
Steel grade | Symbols for the types of hot-dip coating | C | Si | Mn | P | S | Ti | ||||||
DX51D | 1.0226 | +Z,+ZF,+ZA,+AZ,+AS | 0.12 | 0.5 | 0.6 | 0.1 | 0.045 | 0.3 | - | 270 to 500 | 22 | - | - |
DX52D | 1.035 | +Z,+ZF,+ZA,+AZ,+AS | 140 to 300 c | 270 to 420 | 26 | - | - | ||||||
DX53D | 1.0355 | +Z,+ZF,+ZA,+AZ,+AS | 140 to 260 | 270 to 380 | 30 | - | - | ||||||
DX54D | 1.0306 | +Z,+ZA | 120 to 220 | 260 to 350 | 36 | 1,6 | 0,18 | ||||||
DX54D | 1.0306 | +ZF | 120 to 220 | 260 to 350 | 34 | 1,4 | 0,18 | ||||||
DX54D | 1.0306 | +AZ | 120 to 220 | 260 to 350 | 36 | - | - | ||||||
DX54D | 1.0306 | +AS | 120 to 220 | 260 to 350 | 34 | 1,4 d,e | 0,18 e | ||||||
DX55D | 1.0309 | +AS | 140 to 240 | 270 to 370 | 30 | - | - | ||||||
DX56D | 1.0322 | +Z,+ZA | 120 to 180 | 260 to 350 | 39 | 1,9 d | 0,21 | ||||||
DX56D | 1.0322 | +ZF | 120 to 180 | 260 to 350 | 37 | 1,7 d,e | 0,20 e | ||||||
DX56D | 1.0322 | +AS | 120 to 180 | 260 to 350 | 39 | 1,7 d,e | 0,20 e | ||||||
DX57D | 1.0853 | +Z, +ZA | 120 to 170 | 260 to 350 | 41 | 2,1 d | 0,22 | ||||||
DX57D | 1.0853 | +ZF | 120 to 170 | 260 to 350 | 39 | 1,9 d,e | 0,21 e | ||||||
DX57D | 1.0853 | +AS | 120 to 170 | 260 to 350 | 41 | 1,9 d,e | 0,21 e |